Attachment 1584 Details for Bug 2673 – The dmesg after the echo 1 > ... DebugData

The dmesg after the echo 1 > ... DebugData

dmesg (text/plain), 15.00 KB, created by Eric Valette on 2005-11-21 10:07:42 UTC

(hide)

Description:

Filename:

MIME Type:

Creator: Eric Valette

Created: 2005-11-21 10:07:42 UTC

Size: 15.00 KB

patch

obsolete

>it, 0k highmem)
>Checking if this processor honours the WP bit even in supervisor mode... Ok.
>Calibrating delay using timer specific routine.. 3191.43 BogoMIPS (lpj=1595718)
>Mount-cache hash table entries: 512
>CPU: After generic identify, caps: afe9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
>CPU: After vendor identify, caps: afe9f9bf 00000000 00000000 00000000 00000180 00000000 00000000
>CPU: L1 I cache: 32K, L1 D cache: 32K
>CPU: L2 cache: 2048K
>CPU: After all inits, caps: afe9f9bf 00000000 00000000 00000040 00000180 00000000 00000000
>mtrr: v2.0 (20020519)
>CPU: Intel(R) Pentium(R) M processor 1.60GHz stepping 06
>Enabling fast FPU save and restore... done.
>Enabling unmasked SIMD FPU exception support... done.
>Checking 'hlt' instruction... OK.
>ACPI: setting ELCR to 0200 (from 0c00)
>NET: Registered protocol family 16
>ACPI: bus type pci registered
>PCI: PCI BIOS revision 2.10 entry at 0xf031f, last bus=5
>PCI: Using configuration type 1
>usbcore: registered new driver usbfs
>usbcore: registered new driver hub
>ACPI: Subsystem revision 20050902
>ACPI: Interpreter enabled
>ACPI: Using PIC for interrupt routing
>ACPI: PCI Root Bridge [C044] (0000:00)
>PCI: Probing PCI hardware (bus 00)
>ACPI: Assume root bridge [\_SB_.C044] bus is 0
>PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO
>PCI quirk: region 1100-113f claimed by ICH4 GPIO
>PCI: Enabled i801 SMBus device
>PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1
>Boot video device is 0000:01:00.0
>PCI: Transparent bridge - 0000:00:1e.0
>ACPI: PCI Interrupt Routing Table [\_SB_.C044._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.C044.C045._PRT]
>ACPI: PCI Interrupt Routing Table [\_SB_.C044.C056._PRT]
>ACPI: Embedded Controller [C0E7] (gpe 16)
>ACPI: Power Resource [C16D] (on)
>ACPI: Power Resource [C13D] (on)
>ACPI: Power Resource [C184] (on)
>ACPI: Power Resource [C18B] (on)
>ACPI: Power Resource [C195] (on)
>ACPI: Power Resource [C0E6] (on)
>ACPI: PCI Interrupt Link [C0C1] (IRQs *10 11)
>ACPI: PCI Interrupt Link [C0C2] (IRQs 10 *11)
>ACPI: PCI Interrupt Link [C0C3] (IRQs *10 11)
>ACPI: PCI Interrupt Link [C0C4] (IRQs *10 11)
>ACPI: PCI Interrupt Link [C0C5] (IRQs 10 *11)
>ACPI: PCI Interrupt Link [C0C6] (IRQs 10 *11)
>ACPI: PCI Interrupt Link [C0C7] (IRQs 10 11) *0, disabled.
>ACPI: PCI Interrupt Link [C0C8] (IRQs *10 11)
>ACPI: Power Resource [C20B] (off)
>ACPI: Power Resource [C20C] (off)
>ACPI: Power Resource [C20D] (off)
>ACPI: Power Resource [C20E] (off)
>Linux Plug and Play Support v0.97 (c) Adam Belay
>pnp: PnP ACPI init
>pnp: PnP ACPI: found 17 devices
>PnPBIOS: Disabled by ACPI PNP
>SCSI subsystem initialized
>PCI: Using ACPI for IRQ routing
>PCI: If a device doesn't work, try "pci=routeirq".  If it helps, post a report
>Bluetooth: Core ver 2.8
>NET: Registered protocol family 31
>Bluetooth: HCI device and connection manager initialized
>Bluetooth: HCI socket layer initialized
>pnp: 00:0e: ioport range 0x4d0-0x4d1 has been reserved
>pnp: 00:0e: ioport range 0x1000-0x107f could not be reserved
>pnp: 00:0e: ioport range 0x1100-0x113f has been reserved
>pnp: 00:0e: ioport range 0x1200-0x121f has been reserved
>PCI: Bridge: 0000:00:01.0
>  IO window: 2000-2fff
>  MEM window: 90300000-903fffff
>  PREFETCH window: 98000000-9fffffff
>PCI: Bus 3, cardbus bridge: 0000:02:06.0
>  IO window: 00004000-000040ff
>  IO window: 00004400-000044ff
>  PREFETCH window: 50000000-51ffffff
>  MEM window: 58000000-59ffffff
>PCI: Bus 7, cardbus bridge: 0000:02:06.1
>  IO window: 00004800-000048ff
>  IO window: 00004c00-00004cff
>  PREFETCH window: 52000000-53ffffff
>  MEM window: 5a000000-5bffffff
>PCI: Bus 11, cardbus bridge: 0000:02:06.3
>  IO window: 00005000-000050ff
>  IO window: 00005400-000054ff
>  PREFETCH window: 54000000-55ffffff
>  MEM window: 5c000000-5dffffff
>PCI: Bridge: 0000:00:1e.0
>  IO window: 4000-5fff
>  MEM window: 90000000-902fffff
>  PREFETCH window: 50000000-56ffffff
>PCI: Setting latency timer of device 0000:00:1e.0 to 64
>ACPI: PCI Interrupt Link [C0C3] enabled at IRQ 10
>PCI: setting IRQ 10 as level-triggered
>ACPI: PCI Interrupt 0000:02:06.0[A] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10
>ACPI: PCI Interrupt 0000:02:06.1[A] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10
>ACPI: PCI Interrupt 0000:02:06.3[A] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10
>IA-32 Microcode Update Driver: v1.14 <tigran@veritas.com>
>Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
>NTFS driver 2.1.25 [Flags: R/O].
>Initializing Cryptographic API
>io scheduler noop registered
>io scheduler anticipatory registered
>io scheduler deadline registered
>io scheduler cfq registered
>usbmon: debugfs is not available
>ACPI: PCI Interrupt Link [C0C8] enabled at IRQ 10
>ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [C0C8] -> GSI 10 (level, low) -> IRQ 10
>PCI: Setting latency timer of device 0000:00:1d.7 to 64
>ehci_hcd 0000:00:1d.7: EHCI Host Controller
>ehci_hcd 0000:00:1d.7: debug port 1
>ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
>ehci_hcd 0000:00:1d.7: irq 10, io mem 0xa0000000
>PCI: cache line size of 32 is not supported by device 0000:00:1d.7
>ehci_hcd 0000:00:1d.7: USB 2.0 initialized, EHCI 1.00, driver 10 Dec 2004
>hub 1-0:1.0: USB hub found
>hub 1-0:1.0: 6 ports detected
>USB Universal Host Controller Interface driver v2.3
>ACPI: PCI Interrupt Link [C0C1] enabled at IRQ 10
>ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [C0C1] -> GSI 10 (level, low) -> IRQ 10
>PCI: Setting latency timer of device 0000:00:1d.0 to 64
>uhci_hcd 0000:00:1d.0: UHCI Host Controller
>uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
>uhci_hcd 0000:00:1d.0: irq 10, io base 0x000038c0
>hub 2-0:1.0: USB hub found
>hub 2-0:1.0: 2 ports detected
>ACPI: PCI Interrupt Link [C0C4] enabled at IRQ 10
>ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [C0C4] -> GSI 10 (level, low) -> IRQ 10
>PCI: Setting latency timer of device 0000:00:1d.1 to 64
>uhci_hcd 0000:00:1d.1: UHCI Host Controller
>uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
>uhci_hcd 0000:00:1d.1: irq 10, io base 0x000038e0
>hub 3-0:1.0: USB hub found
>hub 3-0:1.0: 2 ports detected
>ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10
>PCI: Setting latency timer of device 0000:00:1d.2 to 64
>uhci_hcd 0000:00:1d.2: UHCI Host Controller
>uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
>uhci_hcd 0000:00:1d.2: irq 10, io base 0x00003c00
>hub 4-0:1.0: USB hub found
>hub 4-0:1.0: 2 ports detected
>usb 3-2: new low speed USB device using uhci_hcd and address 2
>usbcore: registered new driver usblp
>drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
>Initializing USB Mass Storage driver...
>usbcore: registered new driver usb-storage
>USB Mass Storage support registered.
>usbcore: registered new driver hiddev
>input: CHICONY HP Basic USB Keyboard as /class/input/input0
>input: USB HID v1.10 Keyboard [CHICONY HP Basic USB Keyboard] on usb-0000:00:1d.1-2
>usbcore: registered new driver usbhid
>drivers/usb/input/hid-core.c: v2.6:USB HID core driver
>ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [C0C1] -> GSI 10 (level, low) -> IRQ 10
>radeonfb: Retreived PLL infos from BIOS
>radeonfb: Reference=27.00 MHz (RefDiv=6) Memory=250.00 Mhz, System=200.00 MHz
>radeonfb: PLL min 20000 max 35000
>Non-DDC laptop panel detected
>radeonfb: Monitor 1 type LCD found
>radeonfb: Monitor 2 type CRT found
>radeonfb: EDID probed
>radeonfb: panel ID string: QDS                     
>radeonfb: detected LVDS panel size from BIOS: 1400x1050
>radeondb: BIOS provided dividers will be used
>radeonfb: Dynamic Clock Power Management enabled
>Console: switching to colour frame buffer device 175x65
>radeonfb (0000:01:00.0): ATI Radeon NP 
>ACPI: AC Adapter [C134] (on-line)
>ACPI: Battery Slot [C137] (battery present)
>ACPI: Battery Slot [C136] (battery absent)
>ACPI: Power Button (FF) [PWRF]
>ACPI: Sleep Button (CM) [C139]
>ACPI: Lid Switch [C138]
>ACPI: Fan [C20F] (off)
>ACPI: Fan [C210] (off)
>ACPI: Fan [C211] (off)
>ACPI: Fan [C212] (off)
>Using specific hotkey driver
>ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
>ACPI: Processor [CPU0] (supports 8 throttling states)
>ACPI: Thermal Zone [TZ1] (49 C)
>ACPI: Thermal Zone [TZ2] (48 C)
>ACPI: Thermal Zone [TZ3] (29 C)
>isapnp: Scanning for PnP cards...
>isapnp: No Plug & Play device found
>lp: driver loaded but no devices found
>Real Time Clock Driver v1.12
>Non-volatile memory driver v1.2
>hw_random: RNG not detected
>Linux agpgart interface v0.101 (c) Dave Jones
>[drm] Initialized drm 1.0.0 20040925
>ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [C0C1] -> GSI 10 (level, low) -> IRQ 10
>[drm] Initialized radeon 1.19.0 20050911 on minor 0: 
>ipmi message handler version 38.0
>ipmi device interface
>IPMI System Interface driver.
>ipmi_si: Trying "kcs" at I/O port 0xca2
>ipmi_si: Trying "smic" at I/O port 0xca9
>ipmi_si: Trying "bt" at I/O port 0xe4
>ipmi_si: Unable to find any System Interface(s)
>IPMI Watchdog: driver initialized
>Copyright (C) 2004 MontaVista Software - IPMI Powerdown via sys_reboot.
>PNP: PS/2 Controller [PNP0303:C192,PNP0f13:C193] at 0x60,0x64 irq 1,12
>i8042.c: Detected active multiplexing controller, rev 1.1.
>serio: i8042 AUX0 port at 0x60,0x64 irq 12
>serio: i8042 AUX1 port at 0x60,0x64 irq 12
>serio: i8042 AUX2 port at 0x60,0x64 irq 12
>serio: i8042 AUX3 port at 0x60,0x64 irq 12
>serio: i8042 KBD port at 0x60,0x64 irq 1
>Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing disabled
>serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>serial8250: ttyS2 at I/O 0x3e8 (irq = 4) is a 16550A
>00:02: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
>ACPI: PCI Interrupt Link [C0C2] enabled at IRQ 11
>PCI: setting IRQ 11 as level-triggered
>ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C2] -> GSI 11 (level, low) -> IRQ 11
>ACPI: PCI interrupt for device 0000:00:1f.6 disabled
>parport: PnPBIOS parport detected.
>parport0: PC-style at 0x378 (0x778), irq 7, dma 1 [PCSPP,TRISTATE,COMPAT,ECP,DMA]
>lp0: using parport0 (interrupt-driven).
>Floppy drive(s): fd0 is 1.44M
>FDC 0 is a post-1991 82077
>RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
>loop: loaded (max 8 devices)
>pktcdvd: v0.2.0a 2004-07-14 Jens Axboe (axboe@suse.de) and petero2@telia.com
>tg3.c:v3.43 (Oct 24, 2005)
>ACPI: PCI Interrupt Link [C0C5] enabled at IRQ 11
>ACPI: PCI Interrupt 0000:02:0e.0[A] -> Link [C0C5] -> GSI 11 (level, low) -> IRQ 11
>eth0: Tigon3 [partno(BMC5705mA3) rev 3003 PHY(5705)] (PCI:33MHz:32-bit) 10/100/1000BaseT Ethernet 00:12:79:5a:7d:0e
>eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] Split[0] WireSpeed[0] TSOcap[1] 
>eth0: dma_rwctrl[763f0000]
>PPP generic driver version 2.4.2
>PPP Deflate Compression module registered
>PPP BSD Compression module registered
>NET: Registered protocol family 24
>netconsole: not configured, aborting
>Linux video capture interface: v1.00
>Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
>ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
>ICH4: IDE controller at PCI slot 0000:00:1f.1
>PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
>ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [C0C3] -> GSI 10 (level, low) -> IRQ 10
>ICH4: chipset revision 3
>ICH4: not 100% native mode: will probe irqs later
>    ide0: BM-DMA at 0x3c20-0x3c27, BIOS settings: hda:DMA, hdb:pio
>    ide1: BM-DMA at 0x3c28-0x3c2f, BIOS settings: hdc:DMA, hdd:pio
>Probing IDE interface ide0...
>hda: TOSHIBA MK6026GAX, ATA DISK drive
>ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
>Probing IDE interface ide1...
>hdc: SD-R2512, ATAPI CD/DVD-ROM drive
>ide1 at 0x170-0x177,0x376 on irq 15
>hda: max request size: 128KiB
>hda: 117210240 sectors (60011 MB), CHS=65535/16/63, UDMA(100)
>hda: cache flushes supported
> hda: hda1 hda2 < hda5 hda6 hda7 hda8 hda9 hda10 hda11 hda12 hda13 hda14 hda15 >
>hdc: ATAPI 24X DVD-ROM CD-R/RW drive, 2048kB Cache, DMA
>Uniform CD-ROM driver Revision: 3.20
>ieee1394: Initialized config rom entry `ip1394'
>video1394: Installed video1394 module
>ieee1394: raw1394: /dev/raw1394 device initialized
>sbp2: $Rev: 1306 $ Ben Collins <bcollins@debian.org>
>ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1)
>ieee1394: sbp2: Try serialize_io=0 for better performance
>mice: PS/2 mouse device common for all mice
>input: PC Speaker as /class/input/input1
>I2O subsystem v1.288
>i2o: max drivers = 8
>I2O Configuration OSM v1.248
>I2O Bus Adapter OSM v$Rev$
>I2O Block Device OSM v1.287
>I2O SCSI Peripheral OSM v1.282
>I2O ProcFS OSM v1.145
>i2c /dev entries driver
>input: AT Translated Set 2 keyboard as /class/input/input2
>input: ImPS/2 Logitech Wheel Mouse as /class/input/input3
>Bluetooth: HCI USB driver ver 2.9
>usbcore: registered new driver hci_usb
>Bluetooth: HCI UART driver ver 2.2
>Bluetooth: HCI H4 protocol initialized
>Bluetooth: HCI BCSP protocol initialized
>Advanced Linux Sound Architecture Driver Version 1.0.10rc3 (Mon Nov 07 13:30:21 2005 UTC).
>ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [C0C2] -> GSI 11 (level, low) -> IRQ 11
>PCI: Setting latency timer of device 0000:00:1f.5 to 64
>Synaptics Touchpad, model: 1, fw: 5.9, id: 0x1b6eb1, caps: 0xa84793/0x100000
>serio: Synaptics pass-through port at isa0060/serio4/input0
>input: SynPS/2 Synaptics TouchPad as /class/input/input4
>intel8x0_measure_ac97_clock: measured 50445 usecs
>intel8x0: clocking to 48000
>ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [C0C2] -> GSI 11 (level, low) -> IRQ 11
>PCI: Setting latency timer of device 0000:00:1f.6 to 64
>ALSA device list:
>  #0: Intel 82801DB-ICH4 with AD1981B at 0xa0100000, irq 11
>  #1: Intel 82801DB-ICH4 Modem at 0x3400, irq 11
>NET: Registered protocol family 2
>IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
>TCP established hash table entries: 131072 (order: 7, 524288 bytes)
>TCP bind hash table entries: 65536 (order: 6, 262144 bytes)
>TCP: Hash tables configured (established 131072 bind 65536)
>TCP reno registered
>GRE over IPv4 tunneling driver
>ip_conntrack version 2.4 (7168 buckets, 57344 max) - 216 bytes per conntrack
>ip_conntrack_pptp version 3.1 loaded
>ip_tables: (C) 2000-2002 Netfilter core team
>ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.  http://snowman.net/projects/ipt_recent/
>arp_tables: (C) 2002 David S. Miller
>TCP bic registered
>Initializing IPsec netlink socket
>NET: Registered protocol family 1
>NET: Registered protocol family 17
>NET: Registered protocol family 15
>Bluetooth: L2CAP ver 2.8
>Bluetooth: L2CAP socket layer initialized
>Bluetooth: SCO (Voice Link) ver 0.5
>Bluetooth: SCO socket layer initialized
>Bluetooth: RFCOMM socket layer initialized
>Bluetooth: RFCOMM TTY layer initialized
>Bluetooth: RFCOMM ver 1.6
>Bluetooth: BNEP (Ethernet Emulation) ver 1.2
>Bluetooth: BNEP filters: protocol multicast
>Bluetooth: HIDP (Human Interface Emulation) ver 1.1
>Using IPI Shortcut mode
>ACPI wakeup devices: 
>C056 
>ACPI: (supports S0 S3 S4 S5)
>VFS: Mounted root (ext2 filesystem) readonly.
>Freeing unused kernel memory: 228k freed
>input: PS/2 Generic Mouse as /class/input/input5
>Adding 1952960k swap on /dev/hda9.  Priority:-1 extents:1 across:1952960k
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on hda14, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>kjournald starting.  Commit interval 5 seconds
>EXT3 FS on hda12, internal journal
>EXT3-fs: mounted filesystem with ordered data mode.
>tg3: eth0: Link is up at 100 Mbps, full duplex.
>tg3: eth0: Flow control is on for TX and on for RX.
>cdrom: This disc doesn't have any tracks I recognize!
>pktcdvd: writer pktcdvd0 mapped to hdc
>cdrom: open failed.

Actions: View

Attachments on bug 2673: 1572 | 1582 | 1583 | 1584 | 1914 | 1915